RANGKAIAN POWER

Wednesday, February 13, 2013

Skema Ragkaian Power Amplifier 1000 watt

Skema Rangkaian Audio Distributor

Transmit Audio Setup

Introduction:

Setting Up Your Transmitter Audio

Nady SCM-1000 Sudio Condenser Microphone

This page was designed to step you through the several different aspects of setting up your transmit audio from component ordering to individual processor settings necessary in achieving that ultimate SSBaudio that you have been looking for.

First, let me set the record straight; If you are looking for near AM broadcast quality audio on SSB, then this page was designed for you! If you are looki

Wiring diagrams

AUDIO CABLE

MICROPHONE CABLE BALANCED
(ACCORDING TO IEC-NORM):

60 Watt Guitar Amplifier + Tone Control

Rangkaian Guitar Amplifier + Tone Control

The following is a circuit of amplifiers are equipped with the appropriate regulatory tone in use to strengthen the electric guitar, using a single-rail supply of about 60V and capacitor-coupling for the speaker . The advantages for a guitar amplifier are the very simple circuitry, even for comparatively high power outputs, and a certain built-in degree of loudspeaker protection, due to capacitor C8, preventing the voltage supply to be conveyed into loudspeakers in case of output transistors' failure.

Skema Rangkaian Guitar Amplifier + Tone Control

In all cases where Darlington transistors are used as the output devices it is essential that the sensing transistor (Q2) should be in as close thermal contact with the output transistors as possible. Therefore a TO126-case transistor type was chosen for easy bolting on the heatsink, very close to the output pair

R30 must be trimmed in order to measure about half the voltage supply across the positive lead of C7 and ground. A better setting can be done using an oscilloscope, in order to obtain a symmetrical clipping of the output wave form at maximum output power

Note:
To set quiescent current, tide ampare meter in series between supplay with this series, then do the following

Set the volume control to the minimum and Trimmer R3 to its minimum resistance.
Power-on the circuit and adjust R3 to read a current drawing of about 30 to 35mA.
Wait about 15 minutes, watch if the current is varying and readjust if necessary.

List component

R1,R2______________68K 1/4W Resistors
R3________________680K 1/4W Resistor
R4________________220K 1/4W Resistor
R5_________________33K 1/4W Resistor
R6,R16______________2K2 1/4W Resistors
R7__________________5K6 1/4W Resistor
R8,R21____________330R 1/4W Resistors
R9_________________47K 1/4W Resistor
R10_______________470R 1/4W Resistor
R11_________________4K7 1/4W Resistor
R12,R20____________10K 1/4W Resistors
R13_______________100R 1/4W Resistor
R14,R15____________47R 1/4W Resistors
R17,R18,R19_______100K 1/4W Resistors
R22__________________6K8 1W Resistor
R23,R25_____________470R 1/4W Resistors
R24__________________2K 1/2W Trimmer Cermet
R26,R27_______________4K7 1/2W Resistors
R28________________220R 1/2W Resistor
R29__________________2K2 1/2W Resistor
R30_________________50K 1/2W Trimmer Cermet
R31________________68K 1/4W Resistor
R32,R33______________R47 4W Wirewound Resistors

C1,C4,C5,C6________10µF 63V Electrolytic Capacitors
C2_________________47µF 63V Electrolytic Capacitor
C3_________________47pF 63V Ceramic Capacitor
C7_________________15nF 63V Polyester Capacitor
C8_________________22nF 63V Polyester Capacitor
C9________________470nF 63V Polyester Capacitor
C10,C11,C12________10µF 63V Electrolytic Capacitors
C13_______________220µF 63V Electrolytic Capacitor
C14,C15,C17,C18________47µF 63V Electrolytic Capacitors
C16________________100µF 25V Electrolytic Capacitor
C19_________________33pF 63V Ceramic Capacitor
C20_______________1000µF 50V Electrolytic Capacitor

P1,P2______________10K   Potentiometers
P3_________________10K   Potentiometer

D1,D2____________BAT46   100V 150mA Schottky-barrier Diodes
D3_________________LED

Q1,Q3____________BC546    NPN Transistors
Q2_______________BC556    PNP Transistor
Q4,Q5____________BD139    80V 1.5A NPN Transistors
Q6_____________MJ11016   120V 30A NPN Darlington Transistor
Q7_____________MJ11015   120V 30A PNP Darlington Transistor

J1,J2___________6.3mm. Mono Jack sockets
SW1,SW2___________SPST Switches
SPKR______________speakers  8 or 4 Ohm with Minimum power 75W

Rangkaian Pre-Amp Spul Gitar

This is a pre-amp guitar circuit suitable for high impedance type electric guitar pickups. The circuit is based on a uA 741 op-amp (IC1). The IC1 is wired as a non-inverting amplifier. Resistor Variable R1 can be used as a volume controller. Resistor Variable R6 can be used as tone controller. The switch S1 is used to produce “brilliant” or “soft” tonal effects.

Skema rangkaian Pre-Amp sepul gitar

Description Op-Amp UA741 The UA741 is a high performance monolithic operational amplifier constructed on a single silicon chip. It is intented for a wide range of analog applications. * Summing amplifier * Voltage follower * Integrator * Active filter * Function generator The high gain and wide range of operating voltages provide superior performances in integrator, summing amplifier and general feedback applications. The internal compensation network (6dB/ octave) insures stability in closed loop circuits.

Data max Ic UA741 * Symbol Parameter UA741M UA741I UA741C Unit * Supply voltage (VCC) ±22 V * Differential Input Voltage (Vid ) ±30 V * Input Voltage (Vi ) ±15 V * Power Dissipation (Ptot) 500 mW * Storage Temperature Range (Tstg) -65 to +150 °C.

TONE CONTROL GITAR

Rangkaian Sirkuit tone control

Rangkaian Sirkuit tone control-preamplifier pada dasarnya adalah yang paling banyak digunakan dalam kualitas suara tetapi juga membutuhkan dukungan dari kontrol nada dan nada amplifier.nah kontrol kami hadir di sini termasuk dalam kwalitasnya ukuran standar, silakan coba sendiri.

DAFTAR COMPONEN :

Part Total Qty. Keterangan Substitutions C1, C3, C5, C7, C15, C16 6 2.2uf Electrolytic Capacitor C2, C6 2 0.05uF Keramik Disc Capacitor C4 1 0.22uF Disc Capacitor C8, C10 2 0.015uF Keramik Disc Capacitor C9 1 100uF Electrolytic Capacitor C11, C12 , C13, C14 4 0.1uF Keramik Disc Capacitor R1, R4 2 10K 1/4W Resistor R2, R5 2 33K 1/4W Resistor R3, R6 2 4.7K 1/4W Resistor R7 1 2.2K 1/4W Resistor R8, R9, R10, R11 4 50K Linear Pot U1 1 TDA1524A Tone Control IC S1 1 SPST Switch J1, J2, J3, J4 4 RCA Jacks konektor lain dari pilihan Anda MISC 1 Board, Wire, Knobs, 18 Pin Socket

Wednesday, February 13, 2013

SKEMA RANGKAIAN POWER BTL

SKEMA RANGKAIAN AMPLI GUITAR PEAVEY