Monday, February 15, 2016

Kabel tester Paling sederhana



Cara Kerja
1. colokkan hanya kabel ujung 1 yang akan dites ke connector1 apakah lampu led menyala? kabel kondisi tidak ada yang konslet tidak nyala (atau ground putus)  kemudian
2. colokkan kabel ujung 2 ke connector 2 .  Lampu led harusnya nyala semua.  Jika tidak nyala semua kabel ground ada yang putus (+/- putus)...  Jika nyala salah satu kabel +/- ada yang putus  atau connector rusak.

Balance Input untuk Microphone Line

The circuit was designed for providing a microphone line with a balance input signal to improve the quality of sound with sufficient gain and filter.
  • NE5532 – an internally compensated low noise dual operational amplifier with features such as full power bandwidth up to 140 KHz, input noise voltage of 8 nV, common mode rejection ratio, 9 V/us slew rate, high DC voltage gain, 32 V peak to peak voltage swing, wide supply voltage range from 3 V to 12 V, unity gain bandwidth at 10 MHz, and internal frequency compensation
  • TL072 – a low noise JFET input operational amplifier with features such as common-mode input voltage range, high slew rate, operation without latch up, compensated internal frequency, high input impedance at the JFET input stage, low noise, low total harmonic distortion, protected from output short circuit, low input bias and offset currents, wide common-mode and differential voltage ranges, and low power consumption
  • BC560 – a PNP epitaxial planar Silicon enclosed in a 24-pin dual in-line package or 3-pin TO-92 package typically used for switching and AF amplification due to its low noise and high voltage features
The circuit is made up of the audio from the part of input mixing console from the microphone or from any other source made of high level. The input can be used on the circuit itself or be multiplied to a number of channels that can be attached to the circuit. There are several functions that this circuit may illustrate such as reverse face, phantom power, and signal attenuation, to avoid distortions from signals with high level. The switches are made to function as phantom power for S1, mic-line selector for S2, 20 dB attenuation for S3, and phase inversion for S4.
In extreme conditions, the microphone can deliver a signal of 1 mV up to approximately 1 V. signals of around 100 mV to 1 V can be accepted by the line input and provides amplification. To amplify the signal as necessary up to 1 V on peaks, a microphone preamplifier may be used to deliver a low noise signal to the next circuitry. The phantom power supplied to the microphone by the microphone input is around 48 V.
Using the gain control, the amount of gain can be set although there are some consoles where there is no gain control on the line input. For full mixing console, the gain channels are regulating the signal while the rest of the stages will be added to the next stages. An inversion of the signal is possible through the phase button if present. The low frequencies below approximately 100 Hz are cut using the filter while the signal is being attenuated usually at 20 dB.
The mic/line balance input are normally applied to the mixers which are being used in conference rooms, rental sound systems, churches, hotels, and schools. The direct outputs of the mixer can be utilized with other mixers for usages which require flexible zone distribution, room combining recording, post-production, sub-mixing, and other audio applications.

Saturday, January 30, 2016

Skema Apex Bass Gitar Amplifier

http://adf.ly/1WBOfO

Apex b-600


http://adf.ly/1WBMVf

Apex Speaker Protector

http://adf.ly/1WBIGD

Apex B-500 TEF


Varian lain dari Power amplifier Apex b-500 yang dibuat TEF(triple emitter follower),penambahan rangkaian penguat 1 tingkat diatas tr driver.
skema
http://adf.ly/1WBEZJ

Skema APEX B250

http://adf.ly/1WBD97

Skema Speaker Protektor Apex BA 1200

http://adf.ly/1WB7Zs

Skema APEX B 500

suply output/keluaran 500 watt RMS dngn sumber tegangan/voltage simetris ± 90 volt DC. Skema rangkaian power audio amplifier 500 watt apex tersebut bisa dipakai untuk menggerakan speaker dngn impedansi 4 Ω sampai 32 Ω dngn diameter sampai 18 inch.
rangkaian power audio amplifier 500 watt apex tersebut bekerja pada kelas AB dngn konfigurasi transistor dengan tipe push-pull 4 set. Transistor dengan tipe power yg dipakai sbg final pada skema rangkaian power audio amplifier 500 watt apex yaitu 2SC5200 & 2SA1943. Gambar skema rangkaian & daftar komponen untuk membuat power audio amplifier 500 watt apex bisa disimak pada gambar dibawah ini.